Soaring fuel prices have made gas-guzzling cars very unpopular. Welcome to the resurgence of the motorcycle. Why? Because properly maintained motorcycles and motorcycle engines can get between 40 and 60 miles a gallon. Smaller scooters get upwards of 90 miles a gallon, pretty good for an economy with $4-per-gallon gasoline.
Because of this, bike sales have soared. Motorcycle repair, too, can come in handy. Do you have a bike in storage that you haven’t dusted off for awhile? There’s a good chance you can be among those restoring motorcycles so that you can ride your old road hog again.
Restoring your older motorcycle to working condition starts with some basic steps:
Check Fuel
If you didn’t use a fuel stabilizer before you put the bike into storage, drain your old fuel (including tank, fuel lines and carburetor as applicable) before you run the engine, and put new in. Lubricate spark plug ports with a little oil, too, before you start things up.
Check Oil
Change the oil and filter if you didn’t do so before you started. If you did, top levels off.
How Is Your Battery?
Make sure leads are not corroded and that the battery will fully charge and then hold a charge. If it doesn’t, replace the battery.
Inspect The Chain
Because your chain transfers power from the engine to the rear wheel, it is very important that it be in excellent shape. Look the chain over for the following:
— Is the chain the proper tension? You should be able to grasp it in the center and move it about one inch in either direction, up or down.
— Are front and wheel sprocket teeth in good condition? If the teeth have grooves or “waves” in them or they show other signs of wear, you probably need new sprockets (chain will probably show similar wear and need replacement).
— Check every single section of the chain for signs of wear and for proper tension. It should move about an inch when you pull on it. Tighten the chain if it’s loose, and loosen it if it’s tight. If the links themselves are too tight, you might need to replace the whole chain.
— Clean dirt off the chain with a clean towel or rag before you apply lubricant. Make sure you thoroughly lubricate all sprocket teeth and links.
— Lubricate the chain well. Remember that some solvents should not be used with rubber if your chain has rubber parts to it. Use a proper solvent and wipe off any excess lubricant with a clean rag.
— Set chain tension properly by moving your rear wheel and axle forward or backward. Both sides of the axle should be aligned properly before you tighten things up or the chain and sprockets might wear out quickly. Tighten the axle nuts and replace the cotter pin with a new one if needed.
Fluid Levels
Brake, clutch and coolant levels should be checked as necessary. Make sure you replace missing brake fluid with a new container of the same brand you used last time. Let your bike idle for a few minutes before you take off so that all fluids circulate properly.
Tires and Suspension
Inspect everything thoroughly before you take your first ride. If you kept your bike stored upright on a kickstand, make sure your tires aren’t cracked, marked, or flat. In addition, check to make sure tire wear and air levels are good.
Marketing research is conducted by almost very automotive industry to understand market trends and potential customers. A major purpose of marketing research is to find answers for questions and thus to acquire new or updated knowledge. Today’s automotive manufacturing firms conduct comprehensive marketing research to enhance management decision-making by using relevant, accurate and timely information. Automotive marketing research has thus become a crucial part in management decision making.
Automotive marketing research has been conducted to:
Identify customers
Understand needs and requirements of customers
Find out how and where the customers want the products or service
Discover at what price customers will purchase products
Finding answers for these questions helps automotive manufacturing firms to formulate appropriate product development strategies. Information gathered from marketing research need to be analyzed and used while designing and manufacturing new products or before making any modification to existing product line.
Lack of time and strict time schedule always restrict manufacturing firm to conduct automotive marketing research before launching a new product. Mostly, manufacturers develop products without understanding the actual needs of customers; this might result in the fail of products in markets and thus impart huge loss to manufacturing firm. However, service of marketing research companies can be effectively utilized to carry out marketing research. These companies conduct marketing research and find answers for research problems on behalf of their clients.
Marketing research companies collect data from potential customers by conducting or participating in:
Car clinics – Car clinics are the most effective automotive marketing research tool used by marketing researchcompanies to collect data. These companies conduct car clinics in various parts of countries to collect useful information from large numbers of show attendees.
Drive studies – Marketing research companies design and execute open course drive studies and closed course drive studies to collect feedback related to comfort, ride and handling, and powertrain issues. These kinds of feedback are highly valuable for new product development.
Auto show research – Automobile event research is one of the cost effective tools used to collect information on display evaluations, new product designs, feedback on concept vehicles and new technologies etc.
Online research – marketing research companies conduct different kinds of online surveys to collect information related to topics like new product development, pricing research, styling studies, customer satisfaction and so on. They mail a well designed questionnaire to potential customers and thus seek answers to various research questions. Online research is one of the cost effective and efficient automotive marketing research tool used to collect feedback from large number of customers instantly.
Along with the above tools, marketing research companies also collect information over phone. All these automotive marketing tools have high relevance in obtaining accurate and updated customer feedback. Moreover, information thus collected provides a complete knowledge on the likes and desires of potential customers. This knowledge helps a manufacturing firm to design and develop new products by incorporating new features. Launching products with required features helps manufacturing firm to achieve competitive advantage and also to improve sale.
Ethanol cars work in a way very similar to normal gasoline cars, and are a great viable alternative fuel option because of current high gas prices. The only real difference is that ethanol car engines are able to utilize the biofuel ethanol instead of oil based gasoline.
Ethanol fuel itself is extracted from plants such as corn or sugarcane, and refined into an alcohol. This alcohol is suitable to be used as a biofuel in cars and other vehicles. Most hybrid automobile engines that use ethanol can also use gasoline, and are also called flex-fuel engines. The ethanol is injected into the engine in the same way as a non-hybrid automobile engine. Though ethanol gives slightly less miles per gallon than gasoline, it doesn’t create as much air pollution when it is burned.
The similarities between ethanol flex-fuel engines and standard engines make ethanol cars cheaper than most alternative or hybrid vehicles, because they are built in much the same way as a regular engine. Ethanol is actually cheaper in some cases than gasoline, and thus a hybrid that runs on ethanol can be less expensive to operate than a gasoline based vehicle.
Most standard automobiles can even run on a 10% mixture of ethanol in gasoline. Many gas stations around the world offer ethanol as an alternative to gasoline, and in some countries cars are required to run on ethanol.
You can find out more information about Hybrid Cars at ProHybrid.com along with video news, reviews, and tools such as price quotes and an automotive loan calculator.
Traffic is the bane of all commuters, and once you reach your destination you have to park. In most parts of the world, motorcycles and scooters are what many people turn to in order to make the commute faster, easier, and cheaper. The U.S. is not most parts of the world, but were getting better.
When a commuter rides to work on his/her motorcycle, they accomplish several things. They make the highways and streets less congested, because they take up less space. Their lighter vehicles do less damage to the road surface. And when they park, they take up less parking spacesometimes.
Its that parking aspect that some communities have taken to improve by designating certain parking areas specifically for motorcycles. And yet, in other communities, its almost as if they want to discourage people from riding. Thats how different the laws are.
Lets say youre making your commute on your slim, light, Suzuki GSX-R600. If you work in Edmonton, WA, you can park alongside a lot of other bikes in special, no-charge areas. Not only do you save the money you would otherwise pay to park, but with six or more bikes fitting easily into the space one car would use, youre helping other motorists find their parking spaces more easily.
In other cities, however, you would face an entirely different proposition parking your bike. Some cities require all vehicles to park parallel to the curb in areas designated for parallel parking. That might leave you with room for only two bikes is that space, and thats if the city allows more than one vehicle per parking space. Some do not, even when youre talking motorcycles.
The absurdity of that mandate was demonstrated a couple years ago when one city police department started coming down hard on bikes they considered improperly parked. The bikers banded together and appealed to the city to change their rules but no relief was provided. So a plan was hatched. Early one morning, before most commuters were arriving at work, several hundred motorcyclists came in very early and parked one bike to a parking space all over the downtown area. As far as you could see there were acres of unused space between these solitary motorcycles but nowhere at all for people in cars to park. The city quickly changed its ordinances.
While some four-wheeled motorists might complain that it is unfair for motorcyclists to get preferential parking, the fact is, designated motorcycle parking can be created using curb space that is currently going unused. In Denver the citys traffic department was hard at work on a designated motorcycle parking plan when the recession hit. Although it would have cost very little, with budgets in deficit, any non-essential costs were eliminated and the project stalled before it got off the ground.
Nevertheless, the department was working on an eminently sensible plan. City blocks are frequently marked with paint to designate parking spaces, but often there is not enough room near the corners for another space, even though safety research might show that parking would be OK closer to the corner. Voila. Put a little paint on the asphalt and designate this space for motorcycles. Its just that simple. Now commuters who own motorcycles are encouraged to ride rather than drive because they have convenient, free parking, and that helps everyone else in cars. Its a win-win. Plus, motorists who see motorcyclists getting such a nice benefit might decide its time for them to buy that bike theyve wanted for so long and start riding to work, too.
One of the basic cornerstones for receiving the appropriate automotive repairs is to troubleshoot the problem correctly. When a vehicle doesnt start, there can be a number of possibilities about what may be causing the actual problem. When you troubleshoot properly, it eliminates potential issues that aren’t the real auto repair problem and points you in the right direction. After all, there is no more frustrating waste of money or time than repairing or replacing an incorrect automotive part. Here are a few troubleshooting tips that can help you, inform you, and save you time, money, and frustration in getting the correct automotive repairs done as quickly as possible.
When troubleshooting for automotive repairs, starting out simply is the best approach. There are several very common problem areas in auto repairs. Some of them are, as follows: brake repair, no-start problems, suspension issues, rattles, ticks, grind, and crunches, warning lights, and transmission problems. One of the trickiest areas of automotive repairs to troubleshoot involves your electrical system. Your automotive repair shop can start out by examining your fuses and plug wires, or by checking out any starting problems.
While troubleshooting problems can sometimes seem to be daunting, as long as your auto repair center takes the right steps in the right order, youll find out what is really causing your vehicle to malfunction. Once youve analyzed the automotive repairs needed, you can begin moving in the right direction to take care of them. The specific process that the auto repair requires and the ways to get the problem fixed become clear and straightforward.”
Need Auto Repairs? Get expert advice on your Automotive Repairs by contacting our ASE Certified Technicians today at (763) 205-3995 or go to www.discountbrake.net for more information. Our auto repair shop in Blaine, MN proudly serves residents in the areas of Fridley, and Spring Lake Park, Minnesota.